Mighty Ride Moto · Independent Can-Am Spyder Specialists

How Often Does My Can-Am Spyder Need a New Air Filter

Mighty Ride Moto

At Mighty Ride Moto, we recommend replacing your Spyder’s engine air filter at about 9,000 miles—or sooner if BRP specifies a shorter interval or the filter needs it. Follow any calendar limit in your model’s schedule, too.

The work involved depends on the engine. On the older 990/998 V-twins, access can be miserable. On a 1330, this is usually an easy, worthwhile DIY job.

Which engine do you have? GS, RS and ST models use the 998 V-twin, also known by the 990 designation on earlier models. RTs have the 998 for 2010–2013 and the 1330 from 2014 onward. Every F3 has the 1330.

What BRP recommends

These intervals apply to factory engine air filters. When mileage and time are both listed, use whichever comes first. Model families include their S, T and Limited versions where offered.

Spyder model and yearsEngineBRP replacement schedule
GS, 2008–2009; RS/RS-S, 2010–2012; RT family, 2010–2012990/998 V-twin14,000 miles / 22,500 km under the applicable 2012 revised schedule; see the California exception below.
RS/RS-S, 2013–2016; ST family, 2013998 V-twin4,600 miles / 7,500 km.
ST family, 2014–2016; RT family, 2013998 V-twin14,000 miles / 22,500 km or two years.
RT family, 2014–2022; F3 family, 2015–20221330 triple19,000 miles / 30,000 km in the normal-use schedules.
RT and F3 families, 2023–20261330 tripleReplacement is marked across the A and B service columns, beginning with the A service at one year or 9,300 miles / 15,000 km. Continue with the model-year chart’s recurring service pattern.

California exception: BRP’s revised 2008–2012 maintenance supplement excludes vehicles registered in California. Use the applicable original schedule and confirmed updates for those vehicles.

Why the recommendations differ

BRP’s intervals belong to particular models, years and riding conditions. They are not a range from which every owner can choose. The older V-twins have several schedules, and BRP has revised its maintenance guidance over time.

For 2023–2026, the air-filter replacement entry spans both columns of BRP’s A/B chart. Reading it together with the maintenance overview includes replacement at the A service, starting at one year or 9,300 miles. The earlier 19,000-mile figure should not simply be carried forward to these models.

Why MRM recommends 9,000 miles

For Spyders with longer factory intervals, MRM recommends the shorter end: about 9,000 miles. It is a conservative service target for riders who encounter dust between scheduled visits, rounded below BRP’s 9,300-mile figure. A shorter factory interval still takes priority—9,000 miles does not replace a 4,600-mile requirement.

Replace sooner when conditions call for it

The 2023–2026 guides explicitly call for replacement every 9,300 miles / 15,000 km in dusty or wet conditions, regardless of calendar time. That does not cancel an earlier scheduled service. Older guides also call for more frequent attention in dusty or wet use.

Inspect sooner after heavy dust exposure, and replace a damaged, poorly sealing or heavily contaminated filter. If a used Spyder has no filter-service history, inspect it rather than assuming low mileage means it is fine.

The 990/998 job can be miserable

The filter itself is simple. Reaching it is the part that can make you question your afternoon plans.

On the GS, RS, ST and early RT, bodywork and cramped access make this more work than it sounds. The older RT adds an acoustic panel between you and the airbox. Clips, tight clearances and refitting the cover account for much of the frustration.

A capable DIY owner can handle it, but this is a reasonable job to hire out—especially if you are new to removing Spyder bodywork.

Bundle it with throttle-body or spark-plug work

If your 990/998 is already getting its throttle bodies cleaned or spark plugs replaced, get a new air filter at the same time. With the access work already being done, the filter adds almost no labor. Even if it has some mileage left, replacing it then can save paying for the same disassembly again.

The 1330 is a good DIY job

On a 2014-or-newer RT or any F3, access is much friendlier: remove the specified service cover or body panel, then open the filter housing. Comfortable with basic hand tools and panel fasteners? DIY this one.

Follow the panel and fastener procedure for your exact model and year. Work with the engine off and cool, keep loose dirt out of the intake, and seat the new filter and cover correctly. The diagrams below are location guides, not a complete removal procedure.

Where the filters are—and what they look like

Left and right mean the rider’s left and right while seated facing forward. These original schematics show the general filter locations and shapes. They are not to scale; panel details vary by model and year.

F3: 1330 engine

Look behind the left lateral service cover, beside the fuel tank and ahead of the seat. The filter slides out once its housing cover is removed. Some F3-T and F3 Limited models require moving a wiring harness aside for clearance.

Schematic diagram of a Spyder F3 showing the air filter location behind the left lateral service cover, with the pleated cylindrical 1330 filter
Spyder F3 air-filter diagram

The filter is a pleated cylinder with red end rings, BRP reference 707800483. This is also the filter used by 1330-powered RTs; their body-panel access differs from the F3.

Older RT: 2010–2013, 998 engine

Approach from the right side. The filter sits behind the side bodywork and acoustic panel, inside a clipped airbox cover. The highlighted area shows the general access location.

Schematic diagram of a 2010–2013 Spyder RT showing the right-side air filter access area and the rectangular pleated 998 filter
2010–2013 Spyder RT air-filter diagram

The filter is a rectangular pleated panel with a blue sealing frame, BRP reference 707800306. The same filter serves 2013–2016 RS/RS-S models and all ST models.

Early RS: 2010–2012, plus the 2008–2009 GS

The filter is inside the large black airbox above the engine, just ahead of the seat. Removing the side bodywork exposes the housing, whose lid has clips around its perimeter. The highlighted area shows the airbox’s general location.

Schematic diagram of an early Spyder RS showing the airbox above the engine ahead of the seat, with the shallow rectangular early filter
Early Spyder RS air-filter diagram

The early filter is a shallow rectangular panel with a dark frame and mesh support. Its original BRP reference is 707800188.

The RS changed in 2013. A 2013–2016 RS or RS-S uses the 707800306 filter shown in the older-RT section, not the early GS/RS filter pictured here. Before ordering, confirm the current part number for your model year or VIN; similar-looking filters are not necessarily interchangeable.

Can you clean it instead?

The factory paper filter is a replacement item. BRP advises against washing it or blasting it with compressed air. Clean debris out of the housing without pushing dirt toward the engine.

A washable aftermarket filter follows its own manufacturer’s cleaning and oiling instructions. Those procedures do not apply to the factory paper element.

Want help with the awkward one?

Mighty Ride Moto services all Spyder models and years in the Denver–Boulder area. We can replace the filter and bundle it with other work that shares the same access.

Call (720) 655-1335 or text us with your model, year and mileage.