Generated editorial image of a 2014 Can-Am Spyder RS-S in White Satin and Steel Black Metallic with its sport windshield against a blurred autumn background
Mighty Ride Moto · Independent Can-Am Spyder Specialists · All Models. All Years. Fair Prices.

Can-Am Spyder Winter Storage: Good, Better and Best

By Mighty Ride Moto

Good: a properly prepared Spyder in sheltered outdoor parking under a fitted breathable cover. Better: a dry enclosed garage. Best: a dry garage with stable temperature control and managed moisture.

Every option needs fuel preparation, battery care and periodic checks. Start with the storage space you have, then use the checklist below to prepare your GS, RS, RS-S, ST, F3 or RT.

This guide applies to GS, RS, RS-S, ST, RT and F3 Spyders, including 998 and 1330 engines. Use your model-year Operator’s Guide for specifications and procedures; battery access, fluid checks, lubrication points and parking controls vary.

Good, better and best storage options

Generated editorial image of a Carbon Black 2024 Spyder RT Limited with its cover folded back in a carport, with snow beyond
Good: covered outdoor storage
Generated editorial image of a Steel Black Metallic 2015 Spyder RS parked in a dry, unheated home garage in winter
Better: a dry enclosed garage
Generated editorial image of a Carbon Black 2024 Spyder RT Limited in an insulated, climate-controlled garage with a thermostat on the wall
Best: a dry, temperature-controlled garage
ApproachStorage settingWhat still needs attention
GoodSheltered outdoor parking on a firm, well-drained surface, with a fitted, breathable weather-resistant cover.Wind, wetness beneath the cover, snow accumulation, security and a workable battery-care plan.
BetterA dry, enclosed garage or suitable storage unit, even if unheated.Rodents, damp floors, salty meltwater from other vehicles and access to charging power.
BestA dry garage with stable temperature control and managed moisture.All the usual fuel, battery, tire and inspection tasks. Heat does not replace preparation.

These are MRM’s practical categories, not manufacturer ratings. A dry, well-managed unheated garage can be a better choice than a damp garage with a heater.

Good: covered outdoor Spyder storage

If outdoor storage is your available option, choose the spot before buying the cover. Look for firm, level ground that drains away from the Spyder, shelter from prevailing wind, and clearance from roof runoff or falling snow.

The cover needs to fit your actual configuration. A tall windshield, luggage, passenger backrest or accessories can change the fit. It should stay secure without rubbing the paint or loading the windshield. Let the vehicle dry and the exhaust cool before covering it.

Keep ventilation paths open. A waterproof sheet wrapped tightly around a damp Spyder can trap the moisture you are trying to avoid. Check underneath the cover after storms and thawing weather rather than judging protection from the outside.

Make battery access part of the plan. If safe charging power is unavailable, choose the no-outlet battery plan before the weather makes access difficult.

Outdoor storage is a workable compromise, but a cover and fuel stabilizer alone do not make it a complete winter-storage plan.

Better: an enclosed garage

An enclosed garage removes much of the wind, precipitation and direct sun exposure. Before parking, empty the front compartment and any panniers or top case. Remove food, damp clothing and riding gear; dry the compartments, then close and latch them.

Choose a space away from the puddles left by a snow-covered car. Keep snow shovels, ladders and other equipment from falling against the bodywork. Leave enough room to reach the charging connection and inspect all three tires without moving half the garage.

Check the outlet, not just the charger. Confirm that the maintainer is powered with the garage lights off. A switched outlet, tripped GFCI or unplugged extension lead can leave a charger connected but doing nothing. Route cables where a door cannot pinch them.

If renting a storage unit, ask whether vehicle storage is permitted, whether charging is allowed, and when you can access it. “Indoor” is less useful if you cannot inspect the Spyder or maintain its battery.

Best: a dry, temperature-controlled garage

The best arrangement adds a stable environment to the protection of an enclosed garage. Aim for dryness and modest temperature variation rather than making the room as warm as possible.

A small temperature-and-humidity monitor can help you notice changes. Look for condensation on cold metal, dampness inside the cover or persistent wetness on the floor. Address the moisture source and ventilation instead of assuming the thermostat has solved the problem.

Prepare your Spyder in this order

Do these in order; the sections below explain why each step matters.

  1. Deal with known problems first: note leaks, warning messages, weak starting and service due.
  2. Prepare the fuel: fresh approved fuel, correct stabilizer dose, circulated before the final shutdown.
  3. Complete the storage service for your model and transmission.
  4. Clean, dry and empty the Spyder and its compartments.
  5. Set and record cold tire pressures.
  6. Park securely and start battery care, or use the no-outlet plan.
  7. Cover it and note every temporary closure.
  8. Fill in the storage card and keep it with the key.

Preparation every Spyder needs

Fuel preparation

Circulating stabilized fuel matters because it protects the fuel in the pump, lines and injectors as well as the tank. “Full for storage” means the vehicle’s prescribed fill limit, not fuel brimmed into the filler neck.

Stabilizer is preventive. It does not turn old gasoline into fresh fuel. If the Spyder already has questionable fuel, rough running or a fuel smell, address that before putting it away. A stabilizer’s compatibility with a fuel blend does not mean that blend is approved for your Spyder. [Fuel guidance]

Battery maintenance

Identify the battery actually installed; a previous owner may have replaced it. Use a charger or maintainer compatible with its chemistry and capacity, following both sets of instructions. A properly selected automatic maintainer is different from an uncontrolled charger left connected for months.

Find the correct charging connection before plugging in: our Can-Am Spyder battery-maintainer guide explains battery locations, remote posts where fitted, and connecting a charger. Early under-seat connections, 2013 service-cover terminals and later front-compartment access are different. For your machine, see the battery-access section on the GS, RS, RS-S, ST, F3 or RT page.

Start storage with the battery properly charged, then check its condition and the charging arrangement periodically. Disconnecting a battery reduces vehicle-related drain but does not eliminate self-discharge. A sealed AGM battery must not be opened or topped up with water. If a lithium replacement is fitted, follow its particular cold-weather charging limits. [Battery guidance]

Storage service

Spyder storage procedures include an engine-oil and filter change, coolant and brake-fluid checks and a leak inspection. The oil-check procedure differs between 998 and 1330 engines ; an arbitrary cold reading is not a substitute. Check coolant freeze protection if its condition or mixture is uncertain—a full reservoir does not establish freeze protection.

Check the operation of compartment latches and lever pivots. Lubricate only the points specified for the model, using the approved product. For example, the ST storage instructions include front-suspension lubrication points, while the 2024 RT instructions also name key barrels. Do not turn that into a universal instruction to grease every joint, spray an ignition lock with any lubricant, or apply lubricant to the drive belt or brakes.

On SM5 and SM6 models, include the hydraulic clutch system in the applicable checks. Do not apply a manual-clutch checklist to an SE5 or SE6. A problem noted now is far easier to explain than one discovered in spring. [Operator’s Guides]

Tires and parking

The reference is the cold pressure specified for the exact vehicle and tire setup; the sidewall maximum is a tire limit, not a Spyder setting. A recorded reading makes a slow leak noticeable during winter checks.

If using a lift or supports, use suitable equipment and approved support points. Do not improvise a winter-long arrangement on a hydraulic jack. Follow the Spyder’s parking instructions; do not release its parking brake for storage without a properly planned way to prevent movement.

Rodent protection

Food left in compartments or nearby attracts rodents. Where a model’s storage procedure calls for protecting intake or exhaust openings, the risk shifts to spring: a forgotten closure can stop the engine running properly, which is why each one belongs on the storage card.

A cover does not seal the engine compartment. Check accessible areas for nesting material, damaged insulation or droppings. Finding evidence early gives you time to investigate before the next ride.

No outlet where the Spyder is parked?

You have two workable approaches:

  • Keep the battery installed and arrange periodic charging. Start with it charged, keep the charging access clear, and plan safe access to power before it becomes deeply discharged. Check at least monthly during storage and follow the battery maker’s recharge guidance; colder weather does not remove the need to check.
  • Remove the battery for accessible storage and charging. Follow the model-specific removal procedure or have it removed for you. Keep it charged in a cool, dry, ventilated location, protect the terminals against accidental short circuits, and keep it away from children and pets. Battery removal involves different panels and cable work from connecting to remote posts.

Simply disconnecting the battery reduces vehicle-related drain but does not stop self-discharge. A small jump pack is not a months-long maintenance plan. Never attempt to charge a frozen, swollen or leaking battery. Battery storage references.

A practical winter check

Make a short inspection about once a month, and after severe weather if stored outdoors:

  • Check that the cover is secure and dry underneath.
  • Verify the maintainer’s power and status, or carry out the planned battery check.
  • Look beneath the Spyder for fresh drips and around it for rodent activity.
  • Check tire condition and pressure as appropriate.
  • Record anything that changed.

Note each check on the storage card. A photo of the dash and a few pictures of the vehicle taken before covering it make later changes easier to spot.

Should I start the Spyder occasionally to keep the battery charged?

Use a charger or maintainer for battery care rather than relying on short starts. Starting consumes battery energy, and a brief idle is not a dependable way to replace it. The monthly storage check does not require an engine start.

If you are following a model-specific engine-operation instruction or taking a winter ride, first remove every temporary intake/exhaust closure and disconnect the charger. Start outdoors, never in a garage or other enclosed space. An actual ride requires the full pre-ride checks described below.

What if you ride occasionally in winter?

For Denver, Boulder and Front Range owners, the real decision may be between parking until spring and staying ready for suitable riding days. Choose deliberately.

If you ride, remove and account for storage protections, disconnect charging equipment, and complete the normal pre-ride inspection first. A sunny afternoon does not establish safe conditions along the route; shaded ice, grit and cold tires still matter.

Afterward, remove road-treatment residue using the vehicle’s approved cleaning method, allow everything to dry, and restore the storage setup. Update the fuel record and treat newly added fuel according to the stabilizer instructions. A dated note helps prevent accidentally dosing the same tank repeatedly.

Worst-case storage problems and warning signs

Poor storage can lead to more than a flat battery. Serious problems can include freeze damage where coolant protection is inadequate, damaged wiring from rodents, corrosion, or fuel-system problems that need repair.

Pause the spring start or first ride if you find:

  • A strong gasoline smell, wet fuel-system components or a fuel puddle.
  • New coolant leakage, particularly after a hard freeze.
  • A swollen, cracked, leaking or possibly frozen battery—do not try to charge it.
  • Chewed wiring, nesting material or a blocked intake or exhaust.
  • A tire that will not hold pressure, abnormal brake operation or a wheel that will not move normally.
  • Persistent warning messages, repeated no-start attempts or substantially different running behavior.

These signs call for inspection; they do not identify a failed part by themselves. If the Spyder has starting or electrical symptoms, the Spyder won’t-start guide explains what to record and what a BUDS/BUDS2 scan can and cannot show. For a manual model that refuses to change gears, see SM5 and SM6 shifting problems.

Before the first spring ride

Use your storage card to reverse every temporary change. Remove the cover and any intake or exhaust protection, check the battery and connections, inspect for leaks or animal damage, and complete the model-specific pre-ride checks.

Confirm tire pressures, brakes, lights and controls before setting out. Start outdoors, pay attention to warning messages, and make the first ride a short, low-speed check in a suitable area before committing to a longer trip. [Operator’s Guides]

Need help preparing your Spyder or investigating a spring problem? Mighty Ride Moto provides independent Can-Am Spyder service and repair for owners in Broomfield, Denver, Boulder and surrounding Front Range communities. For service due or storage preparation, see our Spyder service and maintenance.

Spyder winter-storage card

Print this card and keep it with the key.

Model / year: ____________________ Mileage: __________
Parked on: __________ Next battery check: __________
Fuel added / treated on: __________ Product / dose: __________
Battery type / charger mode: ___________________________
Charging connector location: __________________________
Cold tire pressures — LF: ______ RF: ______ Rear: ______
Service completed / service due: _______________________
Temporary closures to REMOVE: ________________________

Before starting: remove all closures; disconnect charger; inspect for leaks, rodents and tire damage; complete pre-ride checks.

Specifications and source information

Use the storage, battery, fueling and pre-ride sections for your exact year and model. Manufacturer references include the 2016 Spyder RS/RS-S Operator’s Guide, 2016 Spyder ST Operator’s Guide, 2016 Spyder F3 Operator’s Guide and 2024 Spyder RT Operator’s Guide. Use the linked model instructions for details that differ, including lubrication points and access panels.

Yuasa off-season storage guidance and battery maintenance guidance; follow the instructions for the battery actually fitted.

STA-BIL manufacturer directions and FAQs; use the instructions for your chosen product rather than assuming every stabilizer has the same dose.